Newland HR3260-CS Скачать руководство пользователя страница 147

Страница: 147 / 165

137

Save/Cancel Barcodes

After reading numeric barcode(s), you need to scan the

Save

barcode to save the data. If you scan the

wrong digit(s), you can either scan the

Cancel

barcode and then start the configuration all over again, or

scan the

Delete the Last Digit

barcode

and then

the correct digit, or scan the

Delete All Digits

barcode

and then the digits you want.

For instance, after reading the

Maximum Length

barcode and numeric barcodes

“1”, “2” and “3”, you

scan:



Delete the Last Digit:

The last digit “3” will be removed.



Delete All Digits:

All digits “123” will be removed.



Cancel:

The maximum length configuration will be cancelled. And the scaner is still in the setup

mode.

【

Save

】

【

Cancel

】

【

Delete the Last Digit

】

【

Delete All Digits

】

Содержание HR3260-CS






































































































































































Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды

Newland HR3260-CS, Руководство пользователя

Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды