Newland HR3260-CS Скачать руководство пользователя страница 140

Страница: 140 / 165

【

Enter Setup

】

【

Exit Setup

】

130

Custom Suffix

Enable/Disable Custom Suffix

If custom suffix is enabled, you are allowed to append to the data a user-defined suffix that cannot exceed
10 characters. For example, if the custom suffix is “AB” and the barcode data is “123”, the Host will
receive “123AB”.

【

Disable Custom Suffix

】

【

Enable Custom Suffix

】

Set Custom Suffix

To set a custom suffix, scan the

Set Custom Suffix

barcode and then the numeric barcodes

corresponding to the hexadecimal value of a desired suffix. To save the settings, scan the

Save

barcode.

Note:

A custom suffix cannot exceed 10 characters.

【

Set Custom Suffix

】

Set the custom suffix

to “CODE” (its hexadecimal value is 0x43/0x4F/0x44/0x45):

1. Scan the

Enter Setup

barcode.

2. Scan the

Set Custom Suffix

barcode.

Scan the numeric barcodes “4”,“3”,“4”,“F”,“4”,“4”,“4” and “5”. (See the

Digit

Barcodes

Appendix

)

4. Scan the

Save

barcode. (See the

Save/Cancel Barcodes

Appendix

)

5. Scan the

Enable Custom Suffix

barcode.

6. Scan the

Exit Setup

barcode.

Содержание HR3260-CS






































































































































































Результаты поиска

Содержание HR3260-CS

Отзывы:

Newland HR3260-CS, Руководство пользователя, Страница: 140 / 165

Результаты поиска

Содержание HR3260-CS

Отзывы: