Newland HR3260-CS Скачать руководство пользователя страница 38

Страница: 38 / 165

【

Enter Setup

】

【

Exit Setup

】

Timeout between Decodes (Same Barcode)

Timeout between Decodes (Same Barcode) can avoid undesired rereading of same barcode in a given

period of time.

To enable/disable the Timeout between Decodes (Same Barcode), scan the appropriate barcode below.

Enable Timeout between Decodes:

Do not allow the scanner to re-read same barcode before the

timeout between decodes (same barcode) expires.

Disable Timeout between Decodes:

Allow the scanner to re-read same barcode.

The following parameter sets the timeout between decodes for same barcode. It is programmable in 1ms

increments from 0ms to 65,535ms. The default setting is 1,500ms.

【

Timeout between Decodes (Same Barcode)

】

Set the Timeout between Decodes (Same Barcode) to 2,500ms:

1. Scan the

Enter Setup

barcode.

2. Scan the

Timeout between Decodes (Same Barcode)

barcode.

3. Scan the numeric barcodes

“2”, “5”, “0” and “0”. (See the

Digit Barcodes

Appendix

)

4. Scan the

Save

barcode. (See the

Save/Cancel Barcodes

Appendix

)

5. Scan the

Exit Setup

barcode.

【

Disable Timeout between Decodes

】

【

Enable Timeout between Decodes

】

Содержание HR3260-CS






































































































































































Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды

Newland HR3260-CS, Руководство пользователя

Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды