background image

 

Enter Setup

 

 

117

                                                                                                                                                                                   

**

Exit Setup

 

 

Set Length Range for QR Code 

The  scanner  can  be  configured  to  only  decode  QR  Code  barcodes  with  lengths  that  fall  between 

(inclusive)  the  minimum  and  maximum  lengths.  To  accomplish  it,  you  need  to  set  the  minimum  and 

maximum lengths. 

 

 

 

Set the Minimum Length (Default: 1)

 

 

 

Set the Maximum Length (Default: 1024)

 

 

 

 

Maximum length of a 2D barcode should not exceed 1024 bytes. Minimum length is 

not  allowed  to  be  greater  than  maximum  length.  If  you  only  want  to  read  QR  Code 

barcodes  with  a  specific  length,  set  both  minimum and maximum lengths  to be  that 

desired length. 

 

Set  the  scanner  to  decode  QR  Code  barcodes  containing  between  8  and  12 

bytes:

 

1.  Scan the 

Enter Setup

 barcode. 

2.  Scan the 

Set the Minimum Length

 barcode. 

3. 

Scan the numeric barcode “8”. (See the 

Digit Barcodes

 in 

Appendix

4.  Scan the 

Save

 barcode. (See the 

Save/Cancel Barcodes

 in 

Appendix

5.  Scan the 

Set the Maximum Length

 barcode. 

6. 

Scan the numeric barcode “1”. 

7. 

Scan the numeric barcode “2”. 

8.  Scan the 

Save

 barcode. 

9.  Scan the 

Exit Setup

 barcode. 

Содержание HR3260-CS






































































































































































Отзывы: