Newland HR3260-CS Скачать руководство пользователя страница 47

Страница: 47 / 165

【

Enter Setup

】

【

Exit Setup

】

Chapter 4 Communication Settings

Introduction

Three types of wireless communication between scanner and cradle: synchronous, asynchronous and

batch modes.

Two types of wired communication between cradle and the Host: RS-232 and USB.

Wireless Communication

Wireless communication modes include Synchronous (default), Asynchronous and Batch modes.



Synchronous Mode:

If Zigbee is available, scanned data will be transferred to the cradle

immediately after a good read; if Zigbee is unavailable, the transmission of decoded data cannot be

accomplished.



Asynchronous Mode:

If Zigbee is available, scanned data will be transferred to the cradle

immediately after a good read; if Zigbee is unavailable, the decoded data will be first stored in the

flash memory in a FIFO (first in first out) manner, and be sent automatically to the cradle when

Zigbee becomes available.



Batch Mode:

The decoded data will be stored in the flash memory no matter whether Zigbee is

available or not. To send the stored data to the cradle, you need to insert the scanner in the cradle
and then press “P” button on the cradle.

【

Synchronous Mode

】

【

Asynchronous Mode

】

【

Batch Mode

】

Содержание HR3260-CS






































































































































































Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды

Newland HR3260-CS, Руководство пользователя

Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды