Neousys Technology Nuvo-5002E Скачать руководство пользователя страница 111

Страница: 111 / 128

Nuvo-5000 Series User’s Manual

- 111 -

4.5 Driver Installation

Neousys provides a very convenient utility in “Drivers & Utilities DVD” to allow the

“One-Click” driver installation. This utility automatically detects your Windows operating

system and installs all necessary drivers to your Nuvo-5000 controller with just one mouse

click.

4.5.1

Install All Drivers Using “One-Click” Driver Installation

1. Insert the “Drivers & Utilities DVD” into a USB DVD-drive attached to your Nuvo-5000

series. A setup utility launches and the following dialog appears.

2. Click on the

“Automatic Driver Installation”

. The setup utility will automatically detect

your Windows operating system and install all necessary drivers. According to different

versions of Windows, the installation process takes about 6~8 minutes. Once driver

installation is done, the setup utility reboots your Windows and your system works

normally afterward.

Содержание Nuvo-5002E

























































































































Результаты поиска

Содержание Nuvo-5002E

Отзывы:

Похожие инструкции для Nuvo-5002E

Бренды по названию

Популярные бренды

Neousys Technology Nuvo-5002E, Руководство пользователя

Результаты поиска

Содержание Nuvo-5002E

Отзывы:

Похожие инструкции для Nuvo-5002E

Бренды по названию

Популярные бренды