Neousys Technology Nuvo-5002E Скачать руководство пользователя страница 91

Страница: 91 / 128

Nuvo-5000 Series User’s Manual

- 91 -

3.10 Power on your Nuvo-5000 Controller

For better flexibility of operation, Nuvo-5000 series provides three alternatives to power on

your Nuvo-5000 controller. You can turn on your Nuvo-5000 controller by pressing the

power button, using an external non-latched switch, or by sending a special LAN packet. In

this section, we illustrate these ways to power on your Nuvo-5000 controller.

3.10.1 Power on Using the Power Button

This is the simplest way to turn on your Nuvo-5000 controller. The power button on the front

panel is a non-latched switch and behaves the ATX-mode on/off control. As DC power is

connected, push the power button will turn on the system as well as the PWR LED indicator.

Push the button when system is on will turn off the system. If your operating system

supports ATX power mode (i.e. Microsoft Windows or Linux), push the power button causes

a pre-defined system behavior, such as shutdown or hibernation.

Содержание Nuvo-5002E

























































































































Результаты поиска

Содержание Nuvo-5002E

Отзывы:

Похожие инструкции для Nuvo-5002E

Бренды по названию

Популярные бренды

Neousys Technology Nuvo-5002E, Руководство пользователя

Результаты поиска

Содержание Nuvo-5002E

Отзывы:

Похожие инструкции для Nuvo-5002E

Бренды по названию

Популярные бренды