Neousys Technology Nuvo-5002E Скачать руководство пользователя страница 92

Страница: 92 / 128

Nuvo-5000 Series User’s Manual

- 92 -

3.10.2 Power on Using an External Non-latched Switch

For an application which places Nuvo-5000 controller inside a cabinet, it’s useful to control

the on/off of the system using an external switch. Nuvo-5000 series provides a 2x5, 2.0mm

pitch wafer connector (for detail, please refer to section 2.2.5) for connecting a non-latched

switch and behaves ATX-mode power on/off control. The external non-latched switch acts

exactly the same as the power button on the front panel. To power on Nuvo-5000 controller

using an external non-latched switch (ATX-mode), please follow the steps described below.

1. Prepare a non-latched switch with a 2x5, 2.0mm pitch wafer terminal. Note that the

switch must be connected to pin#1 and pin#2 (polarity is negligible).

2. Connect the wafer terminal to the wafer connector on the front panel of the Nuvo-5000

controller.

3. Push the non-latched switch will turn on the system (the PWR LED indicator on the

front panel is on at the same time). Push the non-latched switch when system is on will

turn off the system. If your operating system supports ATX power mode (i.e. Microsoft

Windows or Linux), push the power button causes a pre-defined system behavior, such

as shutdown or hibernation.

Содержание Nuvo-5002E

























































































































Результаты поиска

Содержание Nuvo-5002E

Отзывы:

Похожие инструкции для Nuvo-5002E

Бренды по названию

Популярные бренды

Neousys Technology Nuvo-5002E, Руководство пользователя

Результаты поиска

Содержание Nuvo-5002E

Отзывы:

Похожие инструкции для Nuvo-5002E

Бренды по названию

Популярные бренды