Neousys Technology Nuvo-5002E Скачать руководство пользователя страница 90

Страница: 90 / 128

Nuvo-5000 Series User’s Manual

- 90 -

3.9

Connect DC Power to your System

Nuvo-5000 series uses a 3-pin pluggable terminal block to accept 8~35V DC power input. It

provides the reliable way for directly wiring the DC power. The pluggable terminal block is

also used to accept ignition signal if MezIO-V20 ignition control module is installed. To

connect DC power via the 3-pin pluggable terminal block, please follow the steps described

below.

1. Make sure the external DC power supply is power off or disconnected before wiring.

2. Get the 3-pin pluggable terminal block from the accessory box. The terminal block fits

the wires with a gauge of 12~24 AWG.

3. Carefully identify the positive and negative contacts of your DC power supply and

pluggable terminal block. The polarities between DC power supply and terminal block

must be positive (+) to positive (+) and ground (GND) to ground (GND).

4. Insert the wires to correct contacts of pluggable terminal block and tighten clamping

screws using a Philips screwdriver.

5. Firmly plug the terminal block into a receptacle on the rear panel, and tighten the

captive screws using a Slotted screwdriver.

Caution

Nuvo-5000 series accepts 8~35 VDC when using terminal block for DC input. Please make

sure the voltage and polarity of DC power is correct before you connect it to Nuvo-5000

controller. Supplying a voltage over 35V or incorrect polarity will damage the system.

Содержание Nuvo-5002E

























































































































Результаты поиска

Содержание Nuvo-5002E

Отзывы:

Похожие инструкции для Nuvo-5002E

Бренды по названию

Популярные бренды

Neousys Technology Nuvo-5002E, Руководство пользователя

Результаты поиска

Содержание Nuvo-5002E

Отзывы:

Похожие инструкции для Nuvo-5002E

Бренды по названию

Популярные бренды