NEC V854 UPD703006 Скачать руководство пользователя страница 271

Страница: 271 / 417

User’s Manual U11969EJ3V0UM00

271

CHAPTER 8 SERIAL INTERFACE FUNCTION

(9) Address coincidence detection

The I

C bus can select the specific slave device when the master transmits the slave address.

Address coincidence detection can be automatically performed by hardware. If the local address is set to the

slave address register (SVA), INTIIC interrupt request generates only when the slave address transmitted from

the master and the address set in SVA coincide or when an extension code is received.

(10) Error detection

The I

C bus can detect transmission errors by comparing the IIC data before transmission starts and that after

transmission ends because the status of the serial bus during transmission (SDA) is captured also to IIC shift

has occurred.

(11) Extension code

(a) Interrupt request (INTIIC) is issued at the fall of the eighth clock by setting the extension code reception

flag (EXC) regarding it as reception of exception code when the higher 4 bits of the reception address

is either “0000” or “1111”.

The local address stored in the slave address register (SVA) is not affected.

(b) The following is set when “111110xx” is set to SVA by 10-bit address transfer and “111110xx0” is

transferred from the master. However, interrupt request (INTIIC) generates at the fall of the eighth clock.

• Coincidence of the higher 4-bit data : EXC = 1

• Coincidence of the 7-bit data

: COI = 1

Therefore, it is performed by software.

For example, LREL is set to 1 and the next communication wait status enters not to operate a device as

a slave after receiving extension code.

Table 8-4. Definition of Extension Code Bit

Slave Address

R/W Bit

Description

0000 000

General call address

0000 000

Start byte

0000 001

CBUS address

0000 010

Address reserved for different bus format

1111 0xx

10-bit slave address specification

(12) Arbitration

When more than one master simultaneously output start conditions (when setting STT =1 before STD = 1 is

set), master communication continues until the data differs while adjusting the clock. This operation is called

arbitration.

The master which is defeated in arbitration sets the ALD bit of the IIC status register (IICS) at the timing at

which the master is defeated in the arbitration, sets both SCL and SDA lines in Hi-Z status, and releases bus.

The arbitration defeat is detected by software when ALD =1 at the next interrupt request generation timing

(the eighth or ninth clock, stop condition detection, etc.).

For the interrupt generation timing, refer to (7) I

C interrupt (INTIIC).

Содержание V854 UPD703006


































































































































































































































































































































































































































Результаты поиска

Содержание V854 UPD703006

Отзывы:

Бренды по названию

Популярные бренды

NEC V854 UPD703006, Руководство пользователя

Результаты поиска

Содержание V854 UPD703006

Отзывы:

Бренды по названию

Популярные бренды