NEC NC1000C Скачать руководство пользователя страница 85

Страница: 85 / 97

LCD Menu

4-5-6. Version

Displays the version information about the projector, optional boards and IMB.

System

Displays the version information of the projector.

←

Selects the item to display.

←

Displays the version information.

• Model

• Serial No.

• Release Package

• Kernel

• U-Boot

• System Files

• Cinema Firmware

• Cinema Data

• ICP Firmware

• ICP ConfigFile

• FMT FPGA

• Slave BIOS

• Slave Firmware

• Opt MCU

• Secure Processor

• Lens

•

Ballast

IMB

Displays the vendor name and version information about the media block (IMB). When the projector is in standby mode, the vendor
name is blank and the version information displays “---”.

←

Displays the vendor name.

←

Displays the version information.

4-5-7. IP Address

Displays the IP address set in the projector.

←

Displays the IP address.

System

Displays the IP address set for the projector (System).

Содержание NC1000C


































































































Результаты поиска

Содержание NC1000C

Отзывы:

Похожие инструкции для NC1000C

Бренды по названию

Популярные бренды

NEC NC1000C, Руководство по установке

Результаты поиска

Содержание NC1000C

Отзывы:

Похожие инструкции для NC1000C

Бренды по названию

Популярные бренды