NEC Express5800/iR120a-1E Скачать руководство пользователя страница 333

Страница: 333 / 378

Upgrading Your Server 11-19

The LockStep feature can be used under the following conditions:

Install two DIMMs that operate in parallel in memory socket.

All the installed DIMMs should have the same capacity.

Run SETUP (see Chapter 4), change parameters appropriately in the menu selected as
shown below, save the settings and exit from SETUP.

Select [Advanced]

→

[Memory Configuration submenu]

→

[Memory RAS Feature]

→

[Lock Step].

Install memory devices in the following order:

The following LockStep cannot be configured:

LockStep between memory channels of different memory controllers (CPU).

LockStep within the same memory channel.

2nd

4th

1st

3rd

6th

2nd

8th

4th

1-CPU configuration

FRONT

REAR

2-CPU configuration

3rd

7th

1st

5th

Содержание Express5800/iR120a-1E



























































































































































































































































































































































































Результаты поиска

Содержание Express5800/iR120a-1E

Отзывы:

NEC Express5800/iR120a-1E, Руководство пользователя, Страница: 333 / 378

Результаты поиска

Содержание Express5800/iR120a-1E

Отзывы: