manualshive.com logo in svg

NEC Express5800/iR120a-1E, Руководство пользователя, Страница: 28 / 378

Поделиться
Скачать
NEC Express5800/iR120a-1E Скачать руководство пользователя страница 28

1-12    Notes on Using Your Server

During Operation

WARNING

Avoid contact with the server during thunderstorms.

Disconnect the power plug from the outlet when a thunderstorm is
approaching. If it starts thundering before you disconnect the power plug, do
not touch any part of the server including the cables. Failure to follow this
warning may cause a fire or an electric shock.

Keep animals away from the server.

Failure to follow this warning may cause a fire or an electric shock.

Do not leave the server with its tray of optical disk drive ejected.

Dust may enter the server through openings and cause malfunctions of the
server. Any person may also bump it and get injured.

Do not pull out or remove the server from the rack unnecessarily.

Do not pull out or remove the server from the rack unnecessarily. Pulling out
or removing the server from the rack may cause not only the server to operate
incorrectly but also the server to fall on people to make them injured.

Stay away from the fan.

Keep your hand or hair away from the cooling fan on the rear of the server.
Failure to follow this warning may get your hand or hair caught in the fan,
resulting in injury.

Содержание Express5800/iR120a-1E



























































































































































































































































































































































































Отзывы:

Нет отзывов