manualshive.com logo in svg

NEC Express5800/iR120a-1E, Руководство пользователя, Страница: 172 / 378

Поделиться
Скачать
NEC Express5800/iR120a-1E Скачать руководство пользователя страница 172

6-4    Installing Windows Server 2003 x64 Editions

INSTALLING Windows Server 2003 x64 Editions

Preparations for Installation

„

 

NEC EXPRESSBUILDER DVD

„

 

Microsoft Windows Server 2003 R2 Standard x64 Edition (CD-ROM)

„

 

Windows Server 2003 x64 Editions Service Pack 2 (CD-ROM)

„

 

User's Guide

„

 

Getting Started

„

 

Windows Server 2003 x64 Edition OEM-Disk for EXPRESSBUILDER

Creating "Windows Server 2003 x64 Edition OEM-Disk for
EXPRESSBUILDER"

Before installing, create Windows Server 2003 x64 Edition OEM-Disk for EXPRESSBUILDER.

NOTE:

 If you have already "Windows Server 2003 x64 Edition

OEM-Disk for EXPRESSBUILDER" for NEC Express5800 Server
which you are going to install Windows Server 2003 x64 Editions,
you do not need to create it again.

You can create Windows Server 2003 x64 Edition OEM-Disk for EXPRESSBUILDER with the
following two procedures.

Содержание Express5800/iR120a-1E



























































































































































































































































































































































































Отзывы:

Нет отзывов