NEC Express5800/iR120a-1E Скачать руководство пользователя страница 169

Страница: 169 / 378

Chapter 6

Installing Windows Server 2003 x64 Editions

This section explains how to install the Windows Server 2003 x64 Editions.

NOTICE

Read the following notes or information before installing the Windows Server 2003 x64 Editions.

Optional Board Supported by NEC EXPRESSBUILDER

The NEC EXPRESSBUILDER DVD attached to your server supports the following optional
boards;

Controllers supporting installation of OS with Express Setup

–

N8103-116A RAID Controller (128MB, RAID0/1)*

–

N8103-117A RAID Controller (128MB, RAID0/1/5/6)*

–

N8103-118A RAID Controller (256MB, RAID0/1/5/6)*

–

Onboard RAID Controller(LSI Embedded MegaRAID



)

Other controllers

–

N8103-104A SAS Controller*

–

N8103-107 SCSI Controller*

–

N8103-115 RAID Controller (512MB, RAID0/1/5/6)*

* Option

Содержание Express5800/iR120a-1E



























































































































































































































































































































































































Результаты поиска

Содержание Express5800/iR120a-1E

Отзывы:

NEC Express5800/iR120a-1E, Руководство пользователя, Страница: 169 / 378

Результаты поиска

Содержание Express5800/iR120a-1E

Отзывы: