manualshive.com logo in svg

NEC Express5800/iR120a-1E, Руководство пользователя, Страница: 105 / 378

Поделиться
Скачать
NEC Express5800/iR120a-1E Скачать руководство пользователя страница 105

Configuring Your Server    4-29

Virtual Disk

Virtual disk is a logical drive defined in disk group. It is recognized as a physical drive by OS. The
allowable number of virtual disks is up to 16 per disk group, or up to 64 per controller.

The figure below shows a sample configuration in which the Onboard RAID Controller (LSI
Embedded MegaRAID

) is connected with two HDDs, creating one Disk Group. Two RAID1

virtual disks (VD) are defined in the Disk Group.

HDD 1

(80 GB)

HDD 2

(80 GB)

RAID Controller

DG0 160 GB

VD1-2
30 GB

VD1-1
30 GB

VD0-1
50 GB

VD0-2
50 GB

VD0 (RAID1)
50 GB

VD1 (RAID1)
30 GB

Parity

The parity means redundant data. A single set of redundant data is created from the data saved in
more than one HDD.

The created redundant data is used for data recovery when a HDD is defected.

Hot-Swap

The hot-swap enables a HDD to be removed (or replaced) under system operation.

Hot-Spare

The hot-spare is prepared as an auxiliary HDD substituting for a defected HDD included in a logical
drive which is configured at a redundant RAID level. Detecting a HDD fault, the system
disconnects the HDD (or makes it offline) and starts rebuild using the hot-spare.

Содержание Express5800/iR120a-1E



























































































































































































































































































































































































Отзывы:

Нет отзывов