NEC Express5800/iR120a-1E Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 378

NEC Express5800/iR120a-1E Скачать руководство пользователя страница 145

Installing Windows Server 2008 5-17

Procedure for License Authentication

Product Key used in the procedure for license authentication should be matched with the COA label
in which the product key contained in Windows Server 2008 is written.

NOTES:

Execute the activation within 60 days.

COA label may be attached to your server.

Updating the System

IMPORTANT:

"Updating the System" disables the Scalable

Networking Pack (SNP) function.
The setting of SNP function may affect the system performance, so
please refer to the attention of SNP detail in the following site before
setting it.
http://www.nec.com/global/prod/express/

Update the system in the situation below:

CPU is expanded (expanded to single processor to multi-processor).

Modified system configuration.

Recovered the system using recovery process.

The system update brings the correction program provided by Microsoft to be applied to reinforce
the system security.

The system update is recommended.

«
...
143
144
145
146
147
...
»

Содержание Express5800/iR120a-1E



























































































































































































































































































































































































Отзывы:

Нет отзывов