NEC Express5800/53Xi Скачать руководство пользователя

Страница: 58 / 83

1. Installing Internal Options

Express5800/53Xi, Y53Xi User's Guide

Chapter 2 Preparations

Put the rear panel of the card to frame guide, then push the card into slot so that connector pins are

surely engaged with the slot.

Change the jumper setting on motherboard depending on the graphics accelerator board.

Install the riser card to the workstation.

Put the riser card to the catch on the chassis, and slide it downward.

Reassemble

the

workstation.

Turn on the power of the workstation. Make sure that no error message appears on the POST

10.

screen.

When the onboard or optional graphics
accelerator board (excluding
Quadro4000 and Quadro5000)
is installed:

When the graphics accelerator board
Quadro4000 or Quadro5000 is installed:

Содержание Express5800/53Xi




















































































Результаты поиска

Содержание Express5800/53Xi

Отзывы:

Похожие инструкции для Express5800/53Xi

Бренды по названию

Популярные бренды

NEC Express5800/53Xi, Руководство пользователя

Результаты поиска

Содержание Express5800/53Xi

Отзывы:

Похожие инструкции для Express5800/53Xi

Бренды по названию

Популярные бренды