NEC Express5800/53Xi Скачать руководство пользователя страница 57

Страница: 57 / 83

1. Installing Internal Options

Express5800/53Xi, Y53Xi User's Guide

Chapter 2 Preparations

1.6

PCI card

The workstation can have PCI card when an optional riser card is installed.

Important You must avoid static electricity to work with the procedure below. For details, see

Chapter 2

(1.2 Anti-static Measures).

(1) Installation

Follow the steps below to install the PCI card. Refer to the manual provided with the board for details.

Before the installation, set the switches and jumpers of the card appropriately referring to the manual

provided with the PCI card, if necessary.

See

Chapter 2

(

1.3 Preparing for Installation and Removal

) for preparations.

Remove the cable from cable band at the center bar, remove

the two screws, and lift the center bar perpendicularly to
remove it.

Secure the riser card to the center bar with four screws.

Remove the cover from the slot.

Note

Keep the removed cover for future use.

Содержание Express5800/53Xi




















































































Результаты поиска

Содержание Express5800/53Xi

Отзывы:

Похожие инструкции для Express5800/53Xi

Бренды по названию

Популярные бренды

NEC Express5800/53Xi, Руководство пользователя

Результаты поиска

Содержание Express5800/53Xi

Отзывы:

Похожие инструкции для Express5800/53Xi

Бренды по названию

Популярные бренды