NEC Express5800/53Xi Скачать руководство пользователя

Страница: 19 / 83

Précautions pour l'usage (il est recommandé de bien lire ces instructions)

Express5800/53Xi, Y53Xi User's Guide

Précautions pour l'usage (il est recommandé de

bien lire ces instructions)

Les informations suivantes sont nécessaires pour utiliser votre poste de travail correctement et sans risque de

vous blesser. Pour les détails concernant les désignations des composants de cette section, veuillez consulter le

Chapitre 1

(

4. Désignations et caractéristiques des composants

Mesures de sécurité

Suivez les instructions données dans ce document pour votre sécurité lorsque vous utilisez le poste de travail.

Ce Guide de l’Utilisateur décrit les parties dangereuses du poste de travail, les risques possibles, et comment s’y

prendre pour les éviter.

Les composants du poste de travail présentant un risque de danger sont indiqués avec une étiquette de mise en

garde placée sur eux ou autour d’eux (ou, dans certains cas, en imprimant les avertissements sur le poste de

travail même). Dans ce Guide de l’Utilisateur ou sur les étiquettes de mise en garde, les termes

AVERTISSEMENT

ATTENTION

sont utilisés pour indiquer un degré de danger. Ces termes sont définis

comme ci-après :

AVERTISSEMENT

Ce terme signale qu’il y a risque de mort ou de blessure.

ATTENTION

Ce terme signale qu'il y a un risque de brûlures, d'autre blessure ou de dégâts matériels.

Les précautions et notices contre les risques sont présentées avec l’un des trois symboles suivants. Les

différents symboles sont définis comme ci-après :

Attention

Ce symbole signale la présence de risque si l'instruction
reste ignorée. Une image dans le symbole illustre le type
de risque.

Actions qui est

interdite

Ce symbole signale des actions qui sont interdites. Une
image dans le symbole illustre une action interdite
particulière.

Action

obligatoire

Ce symbole signale des actions qui sont obligatoires. Une
image dans le symbole illustre une action obligatoire pour
éviter un risque particulier.

Risque de décharge

électrique

Exemple

Ne démontez pas

Exemple

Déconnectez une prise

Содержание Express5800/53Xi




















































































Результаты поиска

Содержание Express5800/53Xi

Отзывы:

Похожие инструкции для Express5800/53Xi

Бренды по названию

Популярные бренды

NEC Express5800/53Xi, Руководство пользователя

Результаты поиска

Содержание Express5800/53Xi

Отзывы:

Похожие инструкции для Express5800/53Xi

Бренды по названию

Популярные бренды