NCR 7448 Workstation Скачать руководство пользователя страница 52

Страница: 52 / 243

3-4

Chapter 3: Installing Optional Hardware Features

How to Install the International VFD Customer Display

Caution: Do not connect the VFD to a power source that is already powered on.

Integrated Mount International VFD Customer Display (Low
Profile/ Telescope)

Remove the Integrated Display Bracket from the back of the International
VFD Customer Display Cabinet.

Route the display cable through the Telescope Mount, the Low Profile
Mount and the Integrated Display Swivel.

Connect the display cable to the International VFD Customer Display

Remove the Escutcheon on the upper cabinet.

Install the International VFD Customer Display assembly into the upper
cabinet.

Connect the display cable to the RS232 port on the workstation.*

* Note: Cable Routing procedure for 7448 workstation -Hard disk

model

Lay the 7448 workstation on its side.

Содержание 7448 Workstation




















































































































































































































































Результаты поиска

Содержание 7448 Workstation

Отзывы:

Похожие инструкции для 7448 Workstation

Бренды по названию

Популярные бренды

NCR 7448 Workstation, Руководство пользователя по оборудованию

Результаты поиска

Содержание 7448 Workstation

Отзывы:

Похожие инструкции для 7448 Workstation

Бренды по названию

Популярные бренды