NCR 7448 Workstation Скачать руководство пользователя страница 187

Страница: 187 / 243

Chapter 5: Crisis Recovery 5-35

NCR 7448 Network Boot Setting with LCD Operator Display

See Keys Used in the Crisis Recovery, BIOS Setup, and BIOS Upgrade in
Appendix A: BIOS.

1.

Turn on the NCR 7448 Workstation power. The workstation displays the
NCR logo.

Caution: Power up the workstations at an interval of at least five seconds if you
are going to turn on more than one workstation.

2.

If the NCR 7448 Workstation installs two or more disks(e.g. Flash and
Hard disks), go to Step 3. If not, go to Step 8.

Press ESC key when the boot manager displays the followings:

PXE-M00: BootManage UNDI, PXE-2.0 (build XXX)

PXE-M00: Initializing: PnP/BEV
PXE-M04: Hold down both shift keys to change bootstrap
selection...

In the boot menu below, select <Enter Setup> by using the Down Arrow key.

Boot Menu

Diskette Drive

+Hard Drive

BootManage UNDI, PXE-2.0 (build XXX)

Содержание 7448 Workstation




















































































































































































































































Результаты поиска

Содержание 7448 Workstation

Отзывы:

Похожие инструкции для 7448 Workstation

Бренды по названию

Популярные бренды

NCR 7448 Workstation, Руководство пользователя по оборудованию

Результаты поиска

Содержание 7448 Workstation

Отзывы:

Похожие инструкции для 7448 Workstation

Бренды по названию

Популярные бренды