NBase Communications NH2001M Скачать руководство пользователя страница 56

Страница: 56 / 72

NH 2001M

NBase Communications

Port Configuration Commands

This chapter contains instructions for configuring and displaying the ports’
parameters with the Command Line Interface. Type

<port-cfg>

to view all

the related commands.

get-port-cfg

The get-port-cfg command displays the current port configuration.

SYS_console>get-port-cfg

PORT_ID LAN_TYPE LINK IF_TYPE SPEED_SEL LAN_SPEED FDPLX ENABLE

=====================================================================

1 ETH10/100 OFF TP ASENSE NONE OFF ON

2 ETH10/100 OFF TP ASENSE NONE OFF ON

Switch is in relax backoff mode.

The information displayed contains:

• An interface number

• LAN type: ETH-10 indicates 10 Mbps Ethernet

ETH-10/100 indicates 10/100 Mbps Ethernet
ETH-100 indicates 100 Mbps Ethernet

• Link status: ON/OFF

• Physical Interface Type: TP or F/O

• Speed selected: FORC10, FORC100, ASENSE

• LAN Speed: 10Mbps, 100Mbps, none

• Full Duplex mode: OFF = Standard Ethernet (default), ON = Full Duplex

• Enable: ON = enabled (default), OFF = disabled

set-port-dplex

Usage:

set-port-dplex

<port_number> {half|full}

The set-port-dplex command specifies if the given port will be active in full-
duplex or in half-duplex (Standard Ethernet) mode. The default is half-duplex.

SYS_console>set-port-dplex 2 full

SYS_console>_

AI2001SB.QXD 4/5/98 11:27 AM Page 48

Содержание NH2001M









































































Результаты поиска

Содержание NH2001M

Отзывы:

Похожие инструкции для NH2001M

Бренды по названию

Популярные бренды

NBase Communications NH2001M, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NH2001M

Отзывы:

Похожие инструкции для NH2001M

Бренды по названию

Популярные бренды