NBase Communications NH2001M Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 72

NBase Communications NH2001M Скачать руководство пользователя страница 39

31

NH 2001M

NBase Communications

IP Commands

This section lists the IP Configuration commands available to the command
line interface. It is separated into different sections to allow simpler lookup: IP
Configuration lists general configuration commands, Ping lists commands per-
taining to the ping ability of the Agent, Address Resolution Protocol lists
ARP-related information.

IP Configuration

get-ip

This command shows the device’s current IP address, if any.

SYS_console> get-ip

--

no IP Config defined

The device has no IP Address defined

SYS_console> _

SYS_console> get-ip

--

IP Config already defined

The device IP address is: 129.001.001.064

SYS_console> _

set-ip

Usage:

set-ip

<IPaddress>

Sets the IP address of the SNMP Agent. If no IP address was previously set
(as is the default factory configuration), the new value will be used immedi-
ately and saved into NVRAM. Otherwise the new value will only be stored in
the NVRAM, and the user must execute a “warm-reset” to effect the change.

AI2001SB.QXD 4/5/98 11:27 AM Page 31

«
...
37
38
39
40
41
...
»

Содержание NH2001M









































































Отзывы:

Нет отзывов