NBase Communications NH2001M Скачать руководство пользователя страница 15

Страница: 15 / 72

TROUBLESHOOTING

The NH2001M are highly reliable units. However, if operating problems
occur, follow the troubleshooting steps below. If you find that the problem
persists, contact your local NBase representative.

Symptom

None of the LEDs lights or blinks.

Cause

The module is defective.

Action

Replace the module.

Symptom

The LINK LED does not light where:

Copper Port

a) The port is configured through software for 10Mbps, no
auto-speed sensing, with a connection to a 10Mbps PC adaptor.

b) The port is configured through software for 100Mbps, no
auto-speed sensing, with a connection to a 100Mbps PC adaptor.

c) The port is configured through software for 10Mbps, no
auto-speed sensing, with a connection to a 10Mbps hub.

d) The port is configured through software for 100Mbps, no
auto-speed sensing, with a connection to a 100Mbps hub.

Cause

a to d) Cable is not suitable or not connected securely.

Action

Check cable connections in all four cases.

Fiber Port

a) The NH2001MFO port is connected to the F/O port of any
100Mbps hub or switch.

Cause

a) F/O cable is not connected securely.

b) NH2001M unit is defective.

Action

a) Check cable connections.

b) Replace the NH2001MFO unit.

NH2001M

NBase Communications

UG2001SB.QXD 4/12/98 1:53 PM Page 9

Содержание NH2001M









































































Результаты поиска

Содержание NH2001M

Отзывы:

Похожие инструкции для NH2001M

Бренды по названию

Популярные бренды

NBase Communications NH2001M, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NH2001M

Отзывы:

Похожие инструкции для NH2001M

Бренды по названию

Популярные бренды