NBase Communications NH2001M Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 72

background image

59

NH 2001M

NBase Communications

USING AN SNMP MANAGER

This chapter contains instructions for the configuration and management
of the NH 2001M with an SNMP Management System (MegaVision).

Configuring the NH 2001M with an SNMP Agent

The NH 2001M with an SNMP Agent board installed is a plug and play
device. Once connected to the network and powered ON, the NH 2001M starts
operating according to factory-set default values. However, to ensure proper
operation and maximum performance specific to your network configuration
and to provide SNMP access, some environment-specific parameters must be
configured through the CLI.

Global Setup

1. Connect a terminal to the NH 2001M.

2. Log in to the Command Line Interface.

3. Initialize all the NH 2001M parameters to their default values. Use the

following command sequence:

init-nvram

warm-reset

4. Wait until you see the LOGIN prompt again. Login to the Command Line
Interface. Now all system parameters have been initialized to their default
values.

AI2001SB.QXD 4/5/98 11:27 AM Page 59

«
...
65
66
67
68
69
...
»

Содержание NH2001M









































































Отзывы:

Нет отзывов

Похожие инструкции для NH2001M

Бренд: CALIENT Страницы: 22

Бренд: Water Witch Страницы: 2

Бренд: Camozzi Страницы: 2

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

Бренд: Kramer Страницы: 61

Бренд: Adler Страницы: 8

PowerSwitch Z9332F-ON

Бренд: Dell EMC Страницы: 16

Бренд: Top View Страницы: 2

Antenna-Disconnect-Switch

Бренд: ADS Страницы: 12

Бренд: Wyrestorm Страницы: 4

Бренд: SMC Networks Страницы: 6

Бренд: Velleman Страницы: 4

Бренд: Kathrein Страницы: 41

Бренд: Santon Страницы: 16

Бренд: CoolGear Страницы: 8

Бренд: Rocstor Страницы: 2

Бренд: EnGenius Страницы: 72

Бренд: KinAn Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды