Navia PN6280 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 40

Navia PN6280 Скачать руководство пользователя страница 4

PN6280_Hardware Design

Copyright © JSC NIIMA PROGRESS and NAVIA LLC
3

................................................................................................. 28

ESD ................................................................................................................................................... 28

RF FEATURES .................................................................................................................................... 30

............................................................................................................................... 30

........................................................................................................................................... 31

................................................................................................................................ 31

STORAGE AND PRODUCTION ......................................................................................................... 34

............................................................................................................................................ 34

....................................................................................................................................... 34

6.2.1 Module confirmation and moisture ............................................................................................. 35

6.2.2 SMT reflow attentions ................................................................................................................. 36

6.2.3 SMT stencil design and the problem of less tin soldering .......................................................... 37

6.2.4 SMT attentions ........................................................................................................................... 37

SAFETY INFORMATION .................................................................................................................... 39

«
...
2
3
4
5
6
...
»

Содержание PN6280









































Отзывы:

Нет отзывов