Navia PN6280 Скачать руководство пользователя страница 32

Страница: 32 / 40

PN6280_Hardware Design

E-GSM900

<-109dBm

DCS1800

<-109dBm

UMTS2100

<-109dBm

UMTS900

<-109dBm

5.2 Data Link

PN6280 supports GPRS/EDGE CLASS 12and HSDPA/HSDPA R8. The actual application depends

on the local network operator.

Table 5-4 Data Link

Version

Function

Max supported

Theoretical max peak rate

PN6280

GPRS

CS4

85.6kbps

PN6280

EDGE

MCS9

236.8kbps

PN6280

HSDPA

Cat10

14.4Mbps

PN6280

HSUPA

Cat6

5.76Mbps

5.3 Antenna Design

The access part of the RF antenna of this product supports the PAD form. The connection between

the module and the main board antenna interface is required to be welded and connected through a

microstrip line or a strip line. The microstrip line or strip line is designed according to the characteristic

impedance of 50 ohm, and the length of the wire is less than 10mm. Reserved

∏

matching network

Antenna efficiency

Antenna efficiency is the ratio of the input power and radiant power. Because of the return loss,

material loss and coupling loss of the antenna, the radiant power is always lower than the input power.

The ratio is recommended to be controlled over 40%(-4dB).

Содержание PN6280









































Результаты поиска

Содержание PN6280

Отзывы:

Navia PN6280, Руководство пользователя, Страница: 32 / 40

Результаты поиска

Содержание PN6280

Отзывы: