Navia PN6280 Скачать руководство пользователя страница 2

Страница: 2 / 40

PN6280_Hardware Design

Notice

Some features of the product and its accessories described herein rely on the software installed,

capacities and settings of local network, and therefore may not be activated or may be limited by local

network operators or network service providers. Thus, the descriptions herein may not exactly match

the product or its accessories which you purchase. JSC NIIMA PROGRESS and NAVIA LLC reserve

the right to change or modify any information or specifications contained in this manual without prior

notice and without any liability.

Copyright

This document contains proprietary technical information which is the property of JSC NIIMA

PROGRESS and NAVIA LLC. Copying of this document and giving it to others and the using or

communication of the contents thereof, are forbidden without express authority. Offenders are liable

utility model or design. All specification supplied herein are subject to change without notice at any

time.

DISCLAIMER

L CONTENTS OF THIS MANUAL ARE PROVIDED “AS IS”. EXCEPT AS REQUIRED BY

APPLICABLE LAWS, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,

INCLUDINGBUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY,

RELIABILITY OR CONTENTS OF THIS MANUAL.TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, IN NO EVENT SHALL JSC NIIMA PROGRESS AND NAVIA LLC BE LIABLE FOR

ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, OR LOSS OF

PROFITS, BUSINESS, REVENUE, DATA, GOODWILL SAVINGS OR ANTICIPATED SAVINGS

REGARDLESS OF WHETHER SUCH LOSSES ARE FORSEEABLE OR NOT.

Содержание PN6280









































Результаты поиска

Содержание PN6280

Отзывы:

Navia PN6280, Руководство пользователя, Страница: 2 / 40

Результаты поиска

Содержание PN6280

Отзывы: