Navia PN6280 Скачать руководство пользователя страница 35

Страница: 35 / 40

PN6280_Hardware Design

6. Storage and Production

6.1 Storage

The rank of moisture proof of the module is level 3. There is an obvious sign on the table of the internal

and the external packaging.

In the vacuum sealed bag, the module can be stored for 180 days when the temperature is below

°C and the humidity is below 90% under good air circulation.

Humidity level is descripted detail as follows:

Table 6-1 Humidity level

Rank

Factory Environment

≦

+30°C /60%RH

No controll < 30°C /85%RH

One year

4 weeks

168 hours

72 hours

48 hours

24 hours

Baking before using, SMT during the time table signs

Notes: Moving, storage, production of module must meet the demand of IPC/JEDEC J-STD-033.

6.2 Production

The module is a humidity sensitive device. If the device needs reflow soldering, disassembly and

maintenance, we must strictly comply with the requirements of humidity sensitive device. If module is

Содержание PN6280









































Результаты поиска

Содержание PN6280

Отзывы:

Navia PN6280, Руководство пользователя, Страница: 35 / 40

Результаты поиска

Содержание PN6280

Отзывы: