Navia PN6280 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 40

Navia PN6280 Скачать руководство пользователя страница 18

PN6280_Hardware Design

Copyright © JSC NIIMA PROGRESS and NAVIA LLC
17

3.2.2 USIM application

USIM card signal group (PIN number: 8, 9, 10, 11), near the USIM card seat on the line. Please note

to increase the ESD protection device.

In order to meet the requirements of 3GPP TS 51.010-1 protocol and EMC certification, the proposed

USIM card is arranged near the position module USIM card interface, and avoid to layout too long

resulting in serious waveform distortion, affecting the signal integrity. USIM_CLK and USIM_DATA

signals are recommended to be protected. Between GND and USIM_VDD in parallel with a 1uF and

33pF capacitors, that can filter out the interference of radio frequency signals.

Figure 3-4 (U)SIM Circuit

3.3 USB Interface

USB application

The USB interface of the module conforms to the USB2.0 specification and electrical characteristics.

Support the low-speed, full-speed and high-speed three operating modes. The data exchange

between the main processor (AP) and the module is mainly completed through the USB interface.

«
...
16
17
18
19
20
...
»

Содержание PN6280









































Отзывы:

Нет отзывов