manualshive.com logo in svg

natus OLYMPIC STERILE-DRIER 43, Инструкция по эксплуатации, Страница: 43 / 62

Поделиться
Скачать
natus OLYMPIC STERILE-DRIER 43 Скачать руководство пользователя страница 43

OLYMPIC STERILE-DRIER 

Model 43/44 Instruction Manual

6-13

Repair Procedures

d

Loosen the set screw, then remove the squirrel cage from the blower 

assembly (see Figure 6.6).

Figure 6.6

Accessing the set screw

e

Within the blower assembly, locate the four nuts that secure the blower 

motor to the blower housing (new devices have four nuts, replacement units 

have two nuts). Loosen, remove, and set aside the nuts and washers.

f

Remove the motor. Clean the blower housing to remove dirt and lint.

g

Remove and save the molded rubber mounting washer. Next, remove the 

grounding wire attached to the blower assembly housing, then remove the 

old motor.

h

Locate the grounding wire attached to the replacement motor provided in 

the blower motor replacement kit.

i

Attach the ground wire on the replacement motor to the original location on 

the blower assembly housing.

To reassemble the new motor and blower:

1

Attach the molded rubber mounting washer.

2

Place the motor in the blower housing, then attach with reserved nuts 

and washers.

3

Insert the squirrel cage into the blower assembly, then tighten the set screw.

4

Place the cover on and secure with the three reserved screws.

Allen (or Torx) driver 
should be placed through 
blower opening and slot 
in squirrel cage to access 
the set screw.

NOTE

#

„

The replacement motor has only two threaded studs (see Figure 6.5); you may have two 
extra sets of washers and nuts.

„

Mating quick disconnect crimp terminals are supplied with the replacement motor 
assembly. Use the terminals to replace butt-splices as applicable.

„

When reassembling the motor and blower assembly, pay attention to the following:

„

Do not over-tighten the inlet cover screws; over-tightening can strip the screw 
threads on the blower housing.

„

Ensure that no unused hardware (e.g., washers, nuts) remains inside the blower 
housing wall.

„

Ensure that motor housing nuts are snug only. Use Loctite

®

 242 locking compound 

(not included) or equivalent on the threads.

„

Ensure that approximately a 1/8-in. (32-mm) gap exists between the squirrel cage 
and the inlet cover.

„

Ensure that the squirrel cage does not rub on the motor screws before and after 
tightening the set screw.

„

Ensure that the set screw bears on the flat of the motor shaft and is firmly tightened.

Содержание OLYMPIC STERILE-DRIER 43































































Отзывы:

Нет отзывов