manualshive.com logo in svg

natus OLYMPIC STERILE-DRIER 43, Инструкция по эксплуатации, Страница: 7 / 62

Поделиться
Скачать
natus OLYMPIC STERILE-DRIER 43 Скачать руководство пользователя страница 7

OLYMPIC STERILE-DRIER

 Model 43/44 Instruction Manual

1-1

S e c t i o n

1

Overview

This manual provides the necessary information to install, maintain, and service the 
Olympic Sterile-Drier

TM

 Model 43/44. The installation and service instructions in 

this manual are intended for use by qualified service technicians.

Conventions

The following conventions are used in this manual.

Symbols

The following symbols are located on the Olympic Driers and their packaging.

Table 1.1

Conventions 

Convention

Description

NOTE

#

Notes provide additional information to clarify a point in the text.

CAUTION

Cautions indicate situations that, if not avoided, could result in minor 
to moderate injury to the patient or operator, or damage to the equipment.

WARNING

Warnings indicate situations that, if not avoided, could result in 
serious injury or death to the patient or operator.

BUTTON

This character style represents buttons and controls that the user 
can touch or press.

Table 1.2

Symbols 

Symbol

Description

Symbol

Description

Caution, hot surfaces

Mains power ON

Caution, read instructions

Neutral (neutral conductor)

Line (hot conductor)

Protective earth (ground)

Mains power OFF

Legal manufacturer

Содержание OLYMPIC STERILE-DRIER 43































































Отзывы:

Нет отзывов