National Instruments GPIB-VXI/C Скачать руководство пользователя страница 66

Страница: 66 / 226

Chapter 3

Local Command Set

GPIB-VXI/C User Manual

3-24

ni.com

Dynamic Configuration Commands and Queries

These dynamic configuration (DC) commands and queries are described in the following
sections:

•

DCBNOSend

•

DCGrantDev

•

DCSystem?

The DC commands are used to configure the VXI system when all of these conditions are
present:

•

The GPIB-VXI/C is the RM.

•

At least one DC device is present in the system.

•

The nonvolatile configuration setup specifies

not

to send

Begin Normal Operation

(user-specified hierarchy).

•

The system is still in the startup Configure substate (

DCBNOSend

has not been sent).

The

DCSystem?

query response indicates whether the system contains a DC device. If the

system is found to be a DC system, the

DCGrantDev

command is used to configure the

Commander/Servant hierarchy. The

DCBNOSend

command is used to end the DC phase and

to cause the system to enter normal operation.

Содержание GPIB-VXI/C



































































































































































































































Результаты поиска

Содержание GPIB-VXI/C

Отзывы:

Похожие инструкции для GPIB-VXI/C

Бренды по названию

Популярные бренды

National Instruments GPIB-VXI/C, Руководство пользователя

Результаты поиска

Содержание GPIB-VXI/C

Отзывы:

Похожие инструкции для GPIB-VXI/C

Бренды по названию

Популярные бренды