National Instruments 776572-00 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 128

background image

© National Instruments Corporation

1-1

SCXI-1100 User Manual

Chapter 1
Introduction

This chapter describes the SCXI-1100; lists the contents of your SCXI-1100 kit; describes the
optional software, optional equipment, and custom cables; and explains how to unpack the
SCXI-1100 kit.

The SCXI-1100 module operates as a fast 32-channel differential multiplexer with an onboard
programmable gain instrumentation amplifier (PGIA). The SCXI-1100 is a module for signal
conditioning of thermocouples, volt sources, millivolt sources, 4 to 20 mA current sources, and
0 to 20 mA process-current sources. If you provide external excitation, you can also measure
thermistors, strain gauges, and RTDs.

The SCXI-1100 operates with full functionality with the National Instruments MIO boards. You
can use the Lab-LC, Lab-NB, Lab-PC, Lab-PC+, and PC-LPM-16 boards with the SCXI-1100,
but these boards can perform only single-channel reads and cannot scan the module. You can
also use the SCXI-1100 with other systems that comply with the specifications given in
Chapter 2, Configuration and Installation. Each SCXI-1100 module multiplexes its 32 input
channels into a single channel of the data acquisition board. You can multiplex several
SCXI-1100s into a single channel, thus greatly increasing the number of analog input signals that
you can digitize.

An additional shielded terminal block has screw terminals for easy signal attachment to the
SCXI-1100. In addition, a temperature sensor for cold-junction compensation of thermocouples
is included on the terminal block. This cold-junction reference (CJR) is either multiplexed with
the 32 channels or jumper connected to a different channel of the data acquisition board.

With the SCXI-1100 module, the SCXI chassis can serve as a fast-scanning signal conditioner
for laboratory testing, production testing, and industrial-process monitoring.

What Your Kit Should Contain

The contents of the SCXI-1100 kit (part number 776572-00) are listed as follows.

Kit Component

Part Number

SCXI-1100 module

181690-01

SCXI-1100 User Manual

320637-01

If your kit is missing any of the components, contact National Instruments.

«
...
12
13
14
15
16
...
»

Содержание 776572-00

































































































































Отзывы:

Нет отзывов

Похожие инструкции для 776572-00

B.LINE OE 3008BL

Бренд: CLAS Страницы: 20

Бренд: Zico Страницы: 19

Бренд: Raisecom Страницы: 29

Бренд: Sony Страницы: 36

Бренд: Sony Страницы: 40

Бренд: Southwire Страницы: 7

15190TMaintenancePRO

Бренд: Southwire Страницы: 33

Бренд: Benning Страницы: 78

Бренд: Minipa Страницы: 36

Бренд: Velleman Страницы: 16

Бренд: Sealey Страницы: 2

Бренд: BASETech Страницы: 80

Бренд: UNI-T Страницы: 2

Бренд: UNI-T Страницы: 2

Бренд: TECPEL Страницы: 25

Бренд: TECPEL Страницы: 47

Бренд: Elma Страницы: 32

Бренд: Delton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды