NanoDrop ND-1000 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 61

background image

Section 16- Troubleshooting

Connection Error

This error occurs whenever the USB connection is disrupted while operating a software module. In most cases, selecting
‘Retry’ will reconnect properly. Some possible causes and solutions are listed below:

Power management scheme on the PC:

If your PC is automatically going into standby or hibernate mode, the USB communication will be lost whenever it occurs
and ‘Retry’ will NOT reconnect the instrument. If this occurs, the USB cable will need to be disconnected/reconnected
before selecting ‘Retry’.

You can confirm that the power management settings are correct by opening the Power Options Properties page by
choosing

Start

Æ

Control Panel

Æ

Power Options

. The ‘System Standby’ and ‘System Hibernate’ should be set to ‘never’

for the ‘Plugged In’ column as shown below.

Static Electricity Discharge

Discharge from the user to the instrument can be a problem in very dry environments. It may be necessary for the user to
wear a grounding strap to prevent the discharges from occurring.

Defective USB Port on PC

If your instrument operates properly most of the time, but the Connection Error appears intermittently, it could be caused
by the USB port on the PC. If this occurs, install the software and operate on another PC. If the error does not occur on
the second PC, it may be necessary to replace the USB card on the original PC.

Signal Error

16-2

«
...
49
50
51
52
53
...
»

Содержание ND-1000






























































Отзывы:

Нет отзывов

Похожие инструкции для ND-1000

Бренд: Kanomax Страницы: 2

Бренд: Keithley Страницы: 156

Бренд: C-LOGIC Страницы: 2

Бренд: E Instruments Страницы: 2

Бренд: Roland Страницы: 15

Бренд: NanoEnTek Страницы: 4

Бренд: Rodstation Страницы: 28

QI-POWER-485-300

Бренд: QEED Страницы: 2

Бренд: Det-Tronics Страницы: 18

Бренд: Omicron Страницы: 76

Бренд: Galileo Страницы: 30

Бренд: Hanna Instruments Страницы: 28

Бренд: Vanguard Instruments Company Страницы: 111

WTW SensoLyt 900

Бренд: Xylem Страницы: 12

Бренд: Vaisala Страницы: 11

Бренд: Barco Страницы: 33

Бренд: Benetech Страницы: 16

Бренд: Maxtec Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды