background image

 

 

mychefcooking.com 

PRODUCT MANUAL    BAKERSHOP     -      DT.MP.BS.2103.2 

49 

8.1.3.

 

Outer housing 

To  clean  the  outer  casing,  use  a  cloth  moistened  with  water  and  dishwashing  soap  or 
specific stainless steel cleaner. Then rinse and dry.   

To clean the glass on the outside through the outer door, use glass cleaner and hand paper 
to avoid scratching the glass. 

 

8.1.4.

 

Control panel 

To clean the control panel, use a cloth dampened with water and dishwashing soap. Then 
rinse and dry. 

Never use agents with alcohols or solvents, as they may attack the metals or plastics in the 
control panel. 

 

8.1.5.

 

Front water drain 

This piece is the one that allows water drops that may fall from the condensation of steam 
from the interior door to go to the drain, so it is important to keep this water collector clean 
and unobstructed. 

Remove any bits of food that may have fallen out before cleaning. Then clean with a cloth 
wet with soap and water and finally rinse with plenty of water. 

 

8.1.6.

 

Interior/exterior door compartment  

To  clean  this  compartment,  the  outer  door  must  be  opened,  and  the  inner  door  clips 
opened so that the door can be opened and the chamber between the outer and inner door 
can be accessed.  

 

Figure 44. Inner glass clamp 

Содержание BAKERSHOP 10 600X400




















































Отзывы: