Murr Elektronik 55530 страница 87 Скачать руководство пользователя

Страница: 87 / 156

Configuration/settings

User manual 55530_hdb_en_16

87 / 156

According to IO-Link integration guideline Edition 1



This type of depiction only provides rudimentary diagnostic options be-

cause several different IO-Link event codes are depicted on the same

PROFINET Channel Error Type.



The PROFINET Channel Error Type therefore only occasionally permits a

conclusion to be drawn about the original IO-Link event code.



"Error"-type IO-Link events are reported as PROFINET diagnostics with

"Fault" maintenance.



Events of the "Warning" type are reported with "Maintenance demanded".



Events of the "Notification" type are not reported as PROFINET diagnos-

tics but are instead handled as "Notifications from the device" in accor-

dance with the parameterization.



The diagnostics do not include any channel numbers.

NOTE

The illustration and overview of the IO-Link event codes on PROFINET diag-

nostics can be found in chap. 9.3.3.1 "According to IO-Link integration guide-

line Edition 1"

Содержание 55530





























































































































































Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды

Murr Elektronik 55530, Руководство пользователя

Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды