Murr Elektronik 55530 Скачать руководство пользователя

Страница: 148 / 156

Operation

User manual 55530_hdb_en_16

148 / 156

0x4510

(17680)

0x1805

(6149)

0x1805

(6149)

Overflow/Overflow control of analog input

The analog signal is above the

nominal range. Check the limits of

the nominal range.

0x4510

(17680)

0x1806

(6150)

0x1806

(6150)

Underflow/Underflow control of the analog

input

The analog signal is below the

nominal range. Check the limits of

the nominal range.

0x4510

(17680)

0x1807

(6151) –

0x1808

(6152)

0x1807

(6151) –

0x1808

(6152)

Device-specific error code

For further details on this IO-Link

event, please read the IO-Link

device manual.

0x4510

(17680)

0x1809

(6153)

0x1809

(6153)

Overriding an analog output caused by ex-

ternal voltage

Check the installation on the ana-

log output.

0x4510

(17680)

0x180A

(6154)

0x180A

(6154)

Underride of an analog output by external

voltage

Test event about checking a noti-

fication

0x4510

(17680)

0x180B

(6155)

0x180B

(6155)

Overload at the analog output

Test event to check an incoming/

outgoing warning

0x4510

(17680)

0x180C

(6156) –

0x181E

(6174)

0x180C

(6156) –

0x181E

(6174)

Device-specific error code

For further details on this IO-Link

event, please read the IO-Link

device manual.

0x4510

(17680)

0x181F

(6175)

0x181F

(6175)

Test event A

Test event for checking an incom-

ing/outgoing error

0x4510

(17680)

0x1820

(6176)

0x1820

(6176)

Test event B

Check the permitted voltage

range

0x4510

(17680)

0x1821

(6177)

0x1821

(6177)

Test event C

Check the permitted voltage

range.

0x4510

(17680)

0x1822

(6178) –

0x1829

(6191)

0x1822

(6178) –

0x1829

(6191)

Device-specific error code

For further details on this IO-Link

event, please read the IO-Link

device manual.

0x4510

(17680)

0x1830

(6192)

0x1830

(6192)

Overvoltage in the secondary power supply

(Port Class B) UA

Check the permitted voltage

range.

0x4510

(17680)

0x1831

(6193)

0x1831

(6193)

Undervoltage in the secondary power sup-

ply (Port Class B) UA

Check the current consumption of

connected consumers.

0x4510

(17680)

0x1832

(6194)

0x1832

(6194)

Error in the secondary voltage (Port Class B)

Check the current consumption of

connected consumers.

0x4510

(17680)

0x1833

(6195)

0x1833

(6195)

Overload of secondary power supply (Port

Class B) UA

Check the installation. Check the

current consumption of the con-

nected consumer.

0x4510

(17680)

0x1834

(6196)

0x1834

(6196)

Overload in the main power supply

Check the installation. Check the

current consumption of the con-

nected consumer.

0x4510

(17680)

0x1835

(6197)

0x1835

(6197)

Overload at the sensor power supply for a

subordinate device

Check the installation. Check the

current consumption of the con-

nected consumer.

0x4510

(17680)

0x1836

(6198)

0x1836

(6198)

Overload of actuator supply for a subordi-

nate device

Check the installation.

0x4510

(17680)

0x1837

(6199)

0x1837

(6199)

Overload of a digital output

Check the installation. Check the

current consumption of the con-

nected consumer.

0x4510

(17680)

0x1838

(6200)

0x1838

(6200)

Override of a digital output by an external

voltage

Check the installation.

0x4510

(17680)

0x1839

(6201) –

0x18FF

(6399)

0x1839

(6201) –

0x18FF

(6399)

Device-specific error code

For further details on this IO-Link

event, please read the IO-Link

device manual.

0x4510

(17680)

0x4000

(16384)

0x4000

(16384)

Temperature error

Overload

0x4510

(17680)

0x4100

(16640)

0x4100

(16640)

Ambient temperature: General fault

Check the ambient temperature.

0x4510

(17680)

0x4110

(16656)

0x4110

(16656)

Admissible ambient temperature exceeded Localize the heat source.

Channel

Error Type

Extended

Channel

Error Type

IO-Link

Event

code(s)

Meaning

Action

Содержание 55530





























































































































































Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды

Murr Elektronik 55530, Руководство пользователя

Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды