Murr Elektronik 55530 страница 104 Скачать руководство пользователя

Страница: 104 / 156

Configuration/settings

User manual 55530_hdb_en_16

104 / 156

IOL_STATUS

The IOL_STATUS consists of 2 bytes of IOL M error codes and 2 bytes of IOL

error types.

FB IO_LINK_DEVICE - Parameter IOL_STATUS / IOL M Error Codes

Tab. 8-42: IOL M Error Codes

FB IO_LINK_DEVICE - Parameter IOL_STATUS / IOL Error Types

Tab. 8-43: IOL Error Types

IOL M Error Codes (2 bytes)
Error Code

Designation according to

spec.

Meaning

0x0000

No error

0x7000

IOL_CALL conflict

Unexpected write request, read request expected

0x7001

Wrong IOL_CALL

Decoding error

0x7002

Port blocked

Port blocked by a different task

...

Reserved

0x8000

Timeout

Timeout, IOL master or IOL device ports overloaded

0x8001

Wrong index

Error: IOL index specified <32767 or >65535

0x8002

Wrong port address

Port address not available

0x8003

Wrong port function

Port function not available

...

Reserved

IOL Error Types (2 bytes)
Error Code

Designation according to

spec.

Meaning

0x1000

COM_ERR

Communication error

Possible cause:

The addressed port is not parametrized as DI and

is not in the IO-Link mode

0x1100

I_SERVICE_TIMEOUT

Timeout in communication, maybe device does not respond quickly

enough

0x5600

M_ISDU_CHECKSUM

Master reports checksum error, access to device not possible

0x5700

M_ISDU_ILLEGAL

Device cannot process request from master

0x8000

APP_DEV

Application error in device

0x8011

IDX_NOTAVAIL

Index not available

0x8012

SUBIDX_NOTAVAIL

Subindex not available

0x8020

SERV_NOTAVAIL

Service temporarily unavailable

0x8021

SERV_NOTAVAIL_LOCCTRL Service temporarily unavailable, device overloaded (e.g. teach-in/

parametrization of device active on device)

0x8022

SERV_NOTAVAIL_DEVCTRL Service temporarily unavailable, device overloaded (e.g. teach-in/

parametrization of device via DTM/PLC, etc., active)

0x8030

PAR_VALOUTOFRNG

Parameter value outside valid range

0x8031

PAR_VALGTLIM

Parameter value above upper limit

0x8032

PAR_VALLTLIM

Parameter value below lower limit

0x8033

VAL_LENOVRRUN

Length of the data to be written does not fit the length defined for the

parameter

0x8034

VAL_LENUNDRUN

0x8035

FUNC_NOTAVAIL

Function in device not available

0x8036

FUNC_UNAVAILTEMP

Function in device temporarily unavailable

0x8040

PARA_SETINVALID

Parameters invalid: Parameters possibly do not fit other parametriza-

tions of the device

0x8041

PARA_SETINCONSIST

Parameters inconsistent

0x8082

APP_DEVNOTRDY

Application not ready, device overloaded

0x8100

UNSPECIFIC

Manufacturer-specific according to device documentation

0x8101 to

0x80FF

VENDOR_SPECIFIC

Содержание 55530





























































































































































Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды

Murr Elektronik 55530, Руководство пользователя

Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды