Murr Elektronik 55530 Скачать руководство пользователя

Страница: 50 / 156

Installation

User manual 55530_hdb_en_16

50 / 156

Sensor supply

Please note:



Sensors can be supplied via

pin 1

(24 V) and

pin 3

(0 V) of the M12 female

connectors.



The maximum permissible current for the power supply of the sensors is

0.2 A

for the digital I/O port and

1.0 A

for the IO-Link port.



In case of overcurrent or short circuit, the connected cable or sensor must

disconnected

from the M12 female connector.

Supported IO-Link

communication

The module supports the IO-Link communication using the following speeds:



4,800 baud (COM 1)



38,400 baud (COM 2)



230,400 baud (COM 3)

NOTE

The MVK module automatically selects the appropriate communication speed

for the IO-Link device.

NOTE

The cable length is limited to 20 m for IO-Link connection.

Содержание 55530





























































































































































Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды

Murr Elektronik 55530, Руководство пользователя

Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды