Murr Elektronik 55530 Скачать руководство пользователя страница 145

Страница: 145 / 156

Operation

User manual 55530_hdb_en_16

145 / 156

0x4500

(17664)

0x4310

(17168)

0x4310

(17168)

Admissible ambient temperature exceeded Localize the heat source.

0x4500

(17664)

0x4320

(17184)

0x4320

(17184)

External temperature dropped below admis-

sible value

Isolate the device.

0x4500

(17664)

0x5000

(20480)

0x5000

(20480)

Hardware error in the device

Replace the device.

0x4500

(17664)

0x5010

(20496)

0x5010

(20496)

Component malfunction

Repair or replace the device.

0x4500

(17664)

0x5011

(20497)

0x5011

(20497)

Loss of non-volatile memory

Check the batteries.

0x4500

(17664)

0x5012

(20498)

0x5012

(20498)

Batteries weak

Replace the batteries.

0x4500

(17664)

0x5100

(20736)

0x5100

(20736)

General fault in supply voltage

Check availability

0x4500

(17664)

0x5101

(20737)

0x5101

(20737)

Fuse blown or off

Replace the fuse or check the

fuse switch

0x4500

(17664)

0x5110

(20752)

0x5110

(20752)

Overvoltage in the main power supply

Check the permitted voltage

range.

0x4500

(17664)

0x5111

(20753)

0x5111

(20753)

Undervoltage in the main power supply

Check the permitted voltage

range.

0x4500

(17664)

0x5112

(20754)

0x5112

(20754)

Faults in the secondary power supply (port

class B)

Check the permitted voltage

range.

0x4500

(17664)

0x5113

(20755)

0x5113

(20755)

Device power supply: Undervoltage U3 =

power 5 V

Check availability

0x4500

(17664)

0x5114

(20756)

0x5114

(20756)

Device power supply: Undervoltage U4 =

vendor-specific

Check availability

0x4500

(17664)

0x5115

(20757)

0x5115

(20757)

Device power supply: Undervoltage U5 =

vendor-specific

Check availability

0x4500

(17664)

0x5116

(20758)

0x5116

(20758)

Device power supply: Undervoltage U6 =

vendor-specific

Check availability

0x4500

(17664)

0x5117

(20759)

0x5117

(20759)

Device power supply: Undervoltage U7 =

vendor-specific

Check availability

0x4500

(17664)

0x5118

(20760)

0x5118

(20760)

Device power supply: Undervoltage U8 =

vendor-specific

Check availability

0x4500

(17664)

0x5119

(20761)

0x5119

(20761)

Device power supply: Undervoltage U9 =

vendor-specific

Check availability

0x4500

(17664)

0x5151

(20817)

0x5151

(20817)

Device power supply: Short circuit

Check the installation.

0x4500

(17664)

0x5160

(20832)

0x5160

(20832)

Device power supply: Fault in the power

supply to peripherals

Check availability

0x4500

(17664)

0x5200

(20992)

0x5200

(20992)

Device controller: General fault

Check the device controller.

0x4500

(17664)

0x5300

(21248)

0x5300

(21248)

Device control panel: General fault

Check the control panel.

0x4500

(17664)

0x5400

(21504)

0x5400

(21504)

Device power unit: General fault

Check the power unit.

0x4500

(17664)

0x5410

(21520)

0x5410

(21520)

Device power supply unit: Fault in the output

driver

Check the installation.

0x4500

(17664)

0x5450

(21584)

0x5450

(21584)

Device power supply unit: Fuse blown or off Replace the fuse or check the

fuse switch

0x4500

(17664)

0x5451

(21585)

0x5451

(21585)

Device power supply unit: Fuse blown or off

S1 = L1

Replace the fuse or check the

fuse switch.

0x4500

(17664)

0x5452

(21586)

0x5452

(21586)

Device power supply unit: Fuse blown or off

S2 = L2

Replace the fuse or check the

fuse switch.

0x4500

(17664)

0x5453

(21587)

0x5453

(21587)

Device power supply unit: Fuse blown or off

S3 = L3

Replace the fuse or check the

fuse switch.

0x4500

(17664)

0x5454

(21588)

0x5454

(21588)

Device power supply unit: Fuse blown or off

S4 = vendor-specific

Replace the fuse or check the

fuse switch.

0x4500

(17664)

0x5455

(21589)

0x5455

(21589)

Device power supply unit: Fuse blown or off

S5 = vendor-specific

Replace the fuse or check the

fuse switch.

Channel

Error Type

Extended

Channel

Error Type

IO-Link

Event

code(s)

Meaning

Action

Содержание 55530





























































































































































Результаты поиска

Содержание 55530

Отзывы:

Бренды по названию

Популярные бренды

Murr Elektronik 55530, Руководство пользователя

Результаты поиска

Содержание 55530

Отзывы:

Бренды по названию

Популярные бренды