Murr Elektronik 55530 Скачать руководство пользователя

Страница: 143 / 156

Operation

User manual 55530_hdb_en_16

143 / 156

9.3.3.2

Murrelektronik IO-Link - Integration and extended integration

The diagnostics listed are available if the parameters for Tab. 8-21: "IO-Link

event integration" are set to "Murrelektronik IO-Link integration" or "Murrelek-

tronik IO-Link extended integration".

Division of diagnostics into value ranges

Tab. 9-24: Division of diagnostics into value ranges

Description of individual diagnostics - master events

Channel Error

Type

Extended Channel Error

Type

IO-Link event code

Meaning

0x4502 (17666) 0x0000 (0) – 0x7FFF (32767)

Master event

0x4500 (17664) 0x0000 (0) – 0x7FFF (32767) 0x0000 (0) – 0x7FFF (32767)

Event from an IO-Link device that

does not support Murrelektronik

IO-Link integration

0x4501 (17665) 0x0000 (0) – 0x7FFF (32767) 0x8000 (32768) – 0xFFFF (65535) Event from an IO-Link device that

does not support the Murrelek-

tronik IO-Link integration.

The Extended Channel Error

Type plus 0x8000 (32768) corre-

sponds to the original IO-Link

event code.

0x4510 (17680) 0x0000 (0) – 0x7FFF (32767) 0x0000 (0) – 0x7FFF (32767)

Event from an IO-Link device that

supports Murrelektronik IO-Link

integration.

The Extended Channel Error

Type corresponds to the original

IO-Link event code.

0x4511 (17681) 0x0000 (0) – 0x7FFF (32767) 0x8000 (32768) – 0xFFFF (65535) Event from an IO-Link device that

supports Murrelektronik IO-Link

integration.

The Extended Channel Error

Type plus 0x8000 (32768) corre-

sponds to the original IO-Link

event code.

Channel Error

Type

Extended Channel

Error Type

Meaning

Action

0x4502 (17666)

Master event

0x4502 (17666) 0x17F0 (6128)

Faults with communication with the

device error memory

0x4502 (17666) 0x1801 (6145)

Faults in start-up parameters

Check the parameterization.

0x4502 (17666) 0x1802 (6146)

Wrong device. Discrepancy in vali-

dation

Connect the correct IO-Link device.

0x4502 (17666) 0x1803 (6147)

Discrepancy in the process data

Check the parameterization for the sub-

module.

0x4502 (17666) 0x1804 (6148)

Short circuit on C/Q - Pin 4

Check the IO-Link device and the wiring.

0x4502 (17666) 0x1805 (6149)

IO-Link PHY overtemperature

Make provision for better heat dissipation.

0x4502 (17666) 0x1806 (6150)

Short-circuit L+ - Pin 1

Check the IO-Link device and the wiring.

0x4502 (17666) 0x1807 (6151)

Undervoltage L+ - Pin 1

Check the sensor supply.

0x4502 (17666) 0x1808 (6152)

Event overflow on the device

Check the IO-Link device.

0x4502 (17666) 0x1809 (6153)

Backup failed.

Memory outside 2k

Check the IO-Link device.

0x4502 (17666) 0x180A (6154)

Inconsistent backup. Data storage

index is not available

Check the IO-Link device.

Содержание 55530





























































































































































Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды

Murr Elektronik 55530, Руководство пользователя

Результаты поиска

Содержание 55530

Отзывы:

Похожие инструкции для 55530

Бренды по названию

Популярные бренды