manualshive.com logo in svg

MTU 20V4000G*3 series, Руководство по эксплуатации

Поделиться
Скачать
MTU 20V4000G*3 series Скачать руководство пользователя страница 236

9.9 Charge-Air Cooling

9.9.1 Intercooler – Checking condensate drain for coolant leak and obstruction

DANGER

Components are moving or rotating.
Risk of crushing, danger of parts of the body being caught or pulled in!
• Operate the engine at low load only. Keep clear of the danger zone of the engine.

WARNING

A high level of noise is produced when the engine is running.
Risk of hearing loss!
• Wear suitable hearing protection.

WARNING

Compressed air gun ejects a jet of pressurized air.
Risk of injury to eyes and damage to hearing, risk of rupturing internal organs!
• Never direct air jet at people.
• Always wear safety goggles/face mask and hearing protection.

Intercooler – Checking conden-
sate drain for coolant leak and
obstruction

1.

With the engine running, verify that air es-
capes from the condensate drain bore(s) at
driving end, left and right engine side. If no
air escapes:
• Clean condensate drain bores
• Blow out condensate drain bores with

compressed air

2.

If a large amount of coolant escapes, the in-
tercooler is leaking. Contact Service.

Emergency measures prior to engine start with a leaking intercooler

1.

Remove injectors (→ Page 211).

2.

Bar engine manually (→ Page 189).

3.

Bar engine with starting system to blow out combustion chambers (→ Page 191).

4.

Install injectors (→ Page 211).

234 | Charge-Air Cooling | MS150093/05E 2018-12

TIM-ID: 0000019861 - 005

Содержание 20V4000G*3 series






















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды