manualshive.com logo in svg

MTU 20V4000G*3 series, Руководство по эксплуатации

Поделиться
Скачать
MTU 20V4000G*3 series Скачать руководство пользователя страница 221

9.8 Fuel Filter

9.8.1 Fuel filter – Replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Filter wrench

F30379104

1

Engine oil
Easy-change filter

(→ Spare Parts Catalog)

WARNING

Fuels are combustible and explosive.
Risk of fire and explosion!
• Avoid open flames, electrical sparks and ignition sources.
• Do not smoke.
• Wear protective clothing, protective gloves, and safety glasses / facial protection.

WARNING

Liquid or gaseous media, e.g. fuel, are poisonous.
Escaping vapors of highly volatile media, e.g. fuel or ether.
Risk of fatal injury through swallowing; risk of poisoning through inhalation; irritation to eyes
and skin!
• Seek medical attention immediately; do not induce vomiting.
• Do not inhale vapors or mist.
• Wear protective clothing, protective gloves, and safety glasses.
• If contact is made with skin, wash off with water and soap.

Replacing fuel filter

1.

Remove easy-change filter using the filter
wrench.

2.

Clean sealing surface on filter head.

3.

Coat seal on easy-change filter slightly with
engine oil (arrowed).

4.

Screw on the easy-change filter by hand until
the seal makes contact and tighten finger-
tight.

5.

Replace further easy-change filters in the
same way.

6.

Vent fuel system (→ Page 217).

MS150093/05E 2018-12

| Fuel Filter | 219

TIM-ID: 0000081192 - 001

Содержание 20V4000G*3 series






















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды