MTS Sensors Temposonics Powerlink V2 R Series Скачать руководство пользователя страница 48

Страница: 48 / 52

Output

Interface

Ethernet POWERLINK

Data protocol

POWERLINK V2 according to IEEE 802.3

Measured value

Position, velocity / option: multi-position measurement (2…4 positions)

Measurement parameters

Resolution

1 μm, 2 μm, 5 μm, 10 μm, 50 μm or 100 μm (selectable)

Cycle time

1.0 ms up to 2400 mm stroke length,

2.0 ms up to 4800 mm stroke length,

4.0 ms up to 7620 mm stroke length

Linearity

< ±0.01 % F.S. (minimum ±50 µm)

Repeatability

< ±0.001 % F.S. (minimum ±2.5 µm) typical

Hysteresis

< 4 µm typical

Temperature coefficient

< 15 ppm/K typical

Operating conditions

Operating temperature

−40…+75 °C (−40…+167 °F)

Humidity

90 % rel. humidity, no condensation

Ingress protection

IP67 (if mating connectors are correctly fitted)

Shock test

100 g (single shock), IEC standard 60068-2-27

Vibration test

15 g (10…2000 Hz), IEC standard 60068-2-6 (resonance frequencies excluded)

EMC test

Electromagnetic immunity EN 61000-6-2

Electromagnetic emission EN 61000-6-3

The sensor meets the requirements of the EC directives and is marked with

Operating pressure

350 bar (5076 psi); Peak: 700 bar (10 007 psi); RH-J: Peak 800 bar (13053.4 psi)

Magnet movement velocity

Any

Design / Material

Sensor electronics housing

Aluminum

Sensor flange

Stainless steel 1.4305 (AISI 303) / RH-J: Stainless steel 1.4305 (AISI 303)

Sensor rod

Stainless steel 1.4306 (AISI 304L) / RH-J: Stainless steel 1.4301 (AISI 304)

Stroke length

25…7620 mm (1…300 in.)

Mechanical mounting

Mounting position

Any

Mounting instruction

Please consult the technical drawings

Electrical connection

Connection type

2 × M12 female connector (4 pin), 1 × M8 male connector (4 pin)

Operating voltage

+24 VDC (−15 / +20 %); UL Recognition requires an approved power supply with energy limitation

(UL 61010-1), or Class 2 rating according to the National Electrical Code (USA) / Canadian Electrical Code.

Ripple

≤ 0.28 V

Current consumption

110 mA typical

Dielectric strength

500 VDC (DC ground to machine ground)

Polarity protection

Up to −30 VDC

Overvoltage protection

Up to 36 VDC

11.2 Technical data of Temposonics

11/

With position magnet # 251 416-2

12/

The IP rating is not part of the UL approval

13/

Power supply must be able to provide current of 1 A for power up process

Temposonics

R-Series Powerlink V2

Operation Manual

I 48 I

Содержание Temposonics Powerlink V2 R Series





















































Результаты поиска

Содержание Temposonics Powerlink V2 R Series

Отзывы:

Бренды по названию

Популярные бренды

MTS Sensors Temposonics Powerlink V2 R Series, Руководство по эксплуатации

Результаты поиска

Содержание Temposonics Powerlink V2 R Series

Отзывы:

Бренды по названию

Популярные бренды