MTD Slalom 67, Инструкция по эксплуатации

Страница: 16 / 30

16
2 - DESCRIPTION
(Fig.1)
4 - ASSEMBLY OF THE GRASS COLLECTION SACK
(Fig.2-3)
3 - TECHNICAL DETAILS
The grass collection sack is included in all the models of the ride-on-mower as a standard
accessory.
For assembly, you need the following parts:
- 1 Frame (1)
- 2 Hexagonal screws (M6x16) (7)
- 2 Washers Ø 6,5x24 (8)
- 2 self-locking nuts (M6) (9)
- 1 Fabric sack with clips
- 2 Z-shaped plates (4)
6 - ASSEMBLY
(Fig.5)
STEERING WHEEL ASSEMBLY
1. Fix the steering wheel (2) pulling until it is connected with the steering column (1).
2. Secure the steering wheel (2) by means of the socket pin (3); put the socket pin through
the openings (at the steering column and steering wheel)
SEAT ASSEMBLY
1- Fasten the seat (4) to the support plate (5) through the 4 M8x18 screws. Assembly with 4
washers Ø 9x24 and 4 groovers.
2- Before tightening the screws, adjust the position of the seat on the holes of the plate
according to the user’s needs.
It is strictly forbidden to start the ride-on-mower (even for trial purposes) without
completing assembly.
The openings at the steering wheel and at the steering column must be in exact
alignment.
7 - ADJUSTING THE CUTTING HEIGHT
(Fig.6-7)
ADJUSTMENT
1. Push the adjustment lever (5) outwards in order to release it from its seat.
2. Push the lever into the required notch for the cutting height.
3. Release the lever slowly till it sticks in the notch.
The cutting height is now set.
EMPTYING THE GRASS COLLECTION BIN
Empty the grass collection bin in time before it overflows.
The red light shows that the bin is full.
Don’t go on filling the grass collection bin when the red light situated under the
steering wheel is on.
Switch off the engine.
1. Hold the rod and swivel the bin. Shake the sack twice until it is completely empty.
2. Let the grass collection sack return slowly to its original position.
3. Switch on the engine.
5 - FRONT WHEEL ASSEMBLY
(Fig.4)
1. Mount the front wheels on the pins (1), positioning a washer (2), the wheel (3) and 2
washers (4).
2. Secure with a stop (5).
G
B
1 Seat 6 Throttle lever 11 Drive pedal
2 Steering wheel 7 Battery 12 Agjusting levers for cutting height
3 Grass catcher bag 8 Blade coupling lever 13 Motor safety houding
4 Blade 9 Brake pedal 14 Pilot light for check-in and for full grass
5 Ignition key 10 Brake lever collection bin
15 Protection casing battery/engine
- 1 Bar (3)
- 2 Self-locking nuts (M8) (6)
- 4 Washers Ø 9x24 (5)
- 2 Plugs Ø 5x50
1- Allow the sack to slide on the frame and secure with suitable clips.
2- Fix the bar with the 4 washers 9x24 (two before and two after the fabric sack) and with the
2 M8 nuts.
Attention: Assemble the wheel with valve outwards
UNPACKING/ ASSEMBLY
The ride-on-mower is packed in a carton and is ready assembled apart from the steering
wheel, seat, grass collection bin and front wheels. Please observe the following sequence
when unpacking the machine:
1. Unpack all the parts that have been delivered. Dispose of the carton and pallet in an
environmentally friendly way.
2. Check all the parts
3. Begin assembly.
Check at regular intervals that the nuts are tightly screwed down.
ASSEMBLY OF THE GRASS COLLECTION SACK
1.Fasten the bin to the rear part of the ride-on-mower with the 2 H.H. 6x16.2 screws, the 2
Z-shaped plates and 2 M6 nuts.
2. Fix the bin cover to the engine casing inserting the two Ø 5x50 plugs
Before the cutting height is adjusted, the engine must be switched off and the
blades must have come to complete standstill.
Engine
Electric starter
Advance
Maximun speed
Grass collection bin
Body
Cutting plate
Cutting width
Cutting height regulation
Curvature radius
Grass collection bag
Tyres
front
rear
Weight with collection bag
Assembled with
Electric
Hydrostatic advance forward and back
8,0 Km/h
2000 mm x 820 mm x 1020 mm
Polypropylene
Sheet steel
0,7 m
150 litri
177 kg
Steering wheel, grass collection bag, front wheels and bin cover
Mod. 76
Briggs & Stratton 12,5 Hp IC OHV
76 cm
Centralised on 4 positions
Mod. 67
Briggs & Stratton 10,5 Hp IC OHV
67 cm
Centralised on 5 positions
Height
265 mm
360 mm
Width
85 mm
120 mm
Recommended pressure
1,5 bar
2 bar
PETROL MOWER WORKING HOURS
Monday to Saturday 08.00 - 12.00 h / 15.00 - 19.00 h
Show respect for those living nearby and avoid using in afternoon rest period, evening or Sundays.
Acoustic power value according to
Directive 2000/14/CE
Acoustic pression power
according to Appendix H from
regulations En836
Vibrations value according to
Appendix G from regulations
En 836
LWA = 96,6 dBA
L eq (dBA) = 82,5
Seat = 2,77 m/s 2
Steering wheel = 2,52 m/s 2
LWA = 98 dBA
L eq (dBA) = 83,1
Seat = 3,25 m/s 2
Steering wheel = 2,77 m/s
2