MSI 3750CS-5 Скачать руководство пользователя страница 8

Страница: 8 / 96

Page 8 MSI-3750CS-5 RF Weighmeter • User Guide

3750CS

ELL

CALE RF DIGITAL WEIGHT INDICATOR

ANTENNAS

To meet FCC licensing rules, you must use only antennas supplied or recommended by MSI. MSI offers the

3750CS with six antenna choices: 1) Standard Antenna – This is a small 1/2 wave antenna that mounts directly

on the 3750CS enclosure and is suitable for most short to medium range applications. 2) Long Range Antenna – A

high gain antenna that is remotely mounted from the 3750CS with a low loss coaxial cable. This omnidirectional

antenna increases the range up to 4 times. The 10' cable allows placement of the antenna above the 3750CS for

ease of clearing possible obstacles to data transmission. 3) Vehicle Mount Whip Antenna – This antenna mounts

directly to the roof of mobile vehicles and is weatherproof. 4) For maximum range, a 14dBi Gain Yagi Antenna

is available by special order. Please contact MSI for details. 5) Corner Reﬂector – Often the best choice for a wall

mounted antenna. MSI offers a 14dBi and a 9dBi Corner Reﬂector. 6) Patch Antenna – For applications where

the standard antenna is vulnerable to physical use or outdoor applications. The Patch antenna is mildly directional

which requires more care in antenna placement for long range applications. Patch Antennas are available by special

order only. See the CellScale Users manual for more details on antennas.
Antenna placement is critical to problem free use of your CellScale system.

1) Be sure a relatively clear transmission path exists between the 3750CS and associated CellScale master devices.

The radio signals travel primarily by line of sight (LOS), and obstructions between stations will degrade the

system performance. LOS is less important as distances decrease.

2) When using the long range antenna, mount the antenna on a tower or other elevated structure to ensure that

you have a clear LOS transmission path. This will raise the antenna to a level sufﬁcient to clear surrounding

terrain and other obstructions. It is not necessary or desirable to provide a ground plane for the antenna.

3) Never use a directional antenna (e.g. a Yagi, or a corner reﬂector) on a mobile system. However, ﬁxed station

locations can often beneﬁt from directional antennas when the location of the other components of the RF

network are always in the same general direction.

4) If using the meter mounted standard antenna, ensure that the antenna is not blocked by any metal. Transmis-

sion is good through most kinds of glass so mounting a meter next to a window should work ﬁne. If there is

no clear line of sight place to mount the 3750CS, consider switching to the long range antenna so the antenna

can be remoted.

5) The standard and long range antennas are vertical plane devices. Do not mount them sideways. They should

always point up (mounted vertically). It also works to point them down, when high off the ground (such as

on the underside of a large bridge crane). The long range 9dBi Antenna is particularly sensitive to off axis

mounting. Use a carpenters level to ensure the antenna is exactly 90° perpendicular to the earth.

6) Do not mount an omnidirectional Antenna next to a metallic or concrete surface. This can result in reﬂections

and undesired RF characteristics. For this application, use a Corner Reﬂector.

7) After installation, you must seal the Antenna connection with an Adhesive Heat Shrink Boot. Failure to seal

the Antenna may result in liquid destroying the Antenna, or the CellScale.

MSI does not recommend extending the coaxial cable beyond 3 meters. At 2.4GHz more loss will result from coax losses than
are gained by raising the antenna. If you must extend the antenna, use a very low loss 50

coax such as RG-214, RF-195, or

other low loss varieties. For very short extensions (<1m), cables made with RG-316 are suitable.

STANDARD ANTENNA

The Standard Antenna (pictured here) is an articulated 1/2 wave 2dBi gain design with a standard TNC

connector. This antenna and Coax connector, though resistant to water, is not water-proof. Seal the

TNC base with an adhesive heat shrink boot if this antenna is exposed to rain. This Antenna should

be vertically oriented.

Содержание 3750CS-5

































































































Результаты поиска

Содержание 3750CS-5

Отзывы:

MSI 3750CS-5, Руководство пользователя, Страница: 8 / 96

Результаты поиска

Содержание 3750CS-5

Отзывы: