MSI 3750CS-5 Скачать руководство пользователя страница 11

Страница: 11 / 96

CellScale

System • 3750CS-5 User Guide Page 11

MEASUREMENT SYSTEMS INTERNATIONAL

Software V2-21 or greater, 2nd Generation Modem

STANDARD ANTENNA BULKHEAD EXTENSIONS

MSI offers short Coaxial cable assemblies to extend the antenna connector when the CellScale equipment is

mounted in an industrial enclosure. These Coaxial assemblies are designed for 2.4Ghz use and have TNC Male

connectors at both ends. These mate with a through panel TNC to TNC Bulkhead Adapter.
TNC to TNC Flange Mount Bulkhead Adapter – MSI P/N 13140
TNC to TNC Jam Nut Mount Bulkhead Adapter – MSI P/N 13141
Extension Coax Cable Assemblies –
1’ (30cm) P/N 13142, 2’ (61cm) P/N 13143, 3’ (.9m) P/N 13144, 4’ (1.2m) P/N 13145

OTHER ANTENNAS

Other antennas are available for special applications. One antenna MSI often uses is a small Patch antenna. This

antenna is suitable for rugged applications where standard antennas will often be destroyed. This is the antenna

used in our Crane Scales. Special antennas for rugged applications, or long range transmission are available.

Contact MSI for more information.

2.4 GHZ INTERFERENCE

Co-Existing with 802.11b Networks
In some cases, if a CellScale network is located in close proximity to an 802.11b network, the CellScale network

can interfere with the 802.11b network. To avoid causing this interference, the CellScale radio supports a selec-

tion of hopping patterns that avoid the various 802.11b direct sequence channels. These limited band hopping

patterns allow CellScale networks to be used with 802.11b networks without impacting the performance of the

802.11b networks. Settings for 802.11b avoidance are found in the Comm Port 2 modem menus. See page 34

for details.

FCC’S MPE REQUIREMENTS

Information to user/installer regarding FCC’s Maximum Permissible Exposure (MPE) limits.

Standard 1/2 Wave Dipole, Patch Antenna, Vehicle Whip, or Long Range 9dBi Omni:

The ﬁeld strength radi-

ated by any one of these antennas, when connected to MSI RF products, may exceed FCC mandated RF exposure

limits. FCC rules require professional installation of these antennas in such a way that the general public will

not be closer than 20 cm from the radiating aperture of any of these antennas. End users of these systems must

also be informed that RF exposure limits may be exceeded if personnel come closer than 20 cm to the apertures

of this antenna.

Corner Reﬂectors or 15dbi Yagi:

The ﬁeld strength radiated by any one of these antennas, when connected to

MSI RF products, may exceed FCC mandated RF exposure limits. FCC rules require professional installation of

these antennas in such a way that the general public will not be closer than 2 m from the radiating aperture of any

of these antennas. End users of these systems must also be informed that RF exposure limits may be exceeded if

personnel come closer than 2 m to the apertures of either of these antennas.

Содержание 3750CS-5

































































































Результаты поиска

Содержание 3750CS-5

Отзывы:

MSI 3750CS-5, Руководство пользователя, Страница: 11 / 96

Результаты поиска

Содержание 3750CS-5

Отзывы: