MSI 3750CS-5 Скачать руководство пользователя страница 77

Страница: 77 / 96

CellScale

System • 3750CS-5 User Guide Page 77

MEASUREMENT SYSTEMS INTERNATIONAL

Software V2-21 or greater, 2nd Generation Modem

SECTION 10 – CELLSCALE CALIBRATION

CALIBRATE GENERAL INFORMATION

The following sections are intended for qualiﬁed scale technicians. The CellScale can be calibrated either directly

using the Terminal Interface mode, or by using a 3750CS. See the CellScale operators guide for information on

direct calibration. This section details the calibration of a CellScale

using the 3750CS RF Weighmeter. Calibrat-

ing a CellScale with a 3750CS Meter requires that adequate test weights (10% of capacity, if the scale is linear),

certiﬁed by the appropriate regulatory agency, are available. See the “Calibration Flowchart” for an overview of

the calibration process.

Calibration constants are stored only in the CellScale. The 3750CS serves only as a controller during calibration.
Since a single CellScale is capable of hosting up to 32 independent scales, the scale to be calibrated must be selected first using the SC Index Key. To Calibrate
multiple Scale Inputs, you must complete the first calibration. Then exit out of the Calibration Menus. Select the next scale with the SC Index Key. Then enable
Calibration again.

NIST Approved Scales: The seal switch on the remote CellScale must be pressed before calibration can begin.

The 3750CS ID must be set as the LFT controller in the CellScale Master.

For a new installation, replacing the CellScale, or setting the Capacity and/or Count-by (d):

1) Select the scale input for calibration using the SC Index Key. See “Accessing multiple scale inputs”.

2) Follow the “Reset Calibration” procedure below.

3) If the unit is legal for trade, set the appropriate standard with the “LEGAL STANDARD” procedure. If the

unit is to be used with metric units only set the standard to “METRIC”, else use “INDUSTRY”.

4) Follow the “CALIBRATION” procedure to set capacity, “d”, and then calibrate.

5) Reseal the Cal’ port when ﬁnished.

For recalibration of a previously calibrated CellScale:

1) Select the scale input for calibration using the SC Index Key. See “Accessing multiple scale inputs”.

2) First follow the “Enable Calibration” procedure below.

3) Next, follow the procedure in the “CALIBRATION” section, skipping steps 3 through 10 as instructed in the

procedure.

4) Reseal the Cal port when ﬁnished.

ENABLE CALIBRATION

To enable the Calibration Menus

DO NOT initiate either of the following two procedures unless you are prepared and qualiﬁed to perform a complete

initialization and/or a calibration procedure. The ﬁrst procedure completely clears the CellScales calibration data for

the chosen scale channel. A full calibration must follow this operation. The second procedure returns all the 3750CS

registers to defaults. However calibration in the CellScale is unaffected.

CALSETUP

STD CAL

1) Expose the Calibration Seal Port by removing the

seal screw on the left side of the 3750 Meter Casting

with a Phillips Head Screwdriver.

2) Insert a small non-metallic screwdriver or the wooden

stem of a “Q-Tip” and press the switch button in the

hole. The display reads “CALSETUP”.

Tip: A wooden Golf Tee fits the hole perfectly.

3) After 3 seconds the Calibrate Setup Menu appears

(STD CAL). Use the UP or DOWN scroll keys to

locate the desired Calibrate operation as described

in the following procedures.

Содержание 3750CS-5

































































































Результаты поиска

Содержание 3750CS-5

Отзывы:

MSI 3750CS-5, Руководство пользователя, Страница: 77 / 96

Результаты поиска

Содержание 3750CS-5

Отзывы: